Immobilizer

This function is to be used when programming a new ignition key or re-programming an existing. It will program the WIN functionality along with the RKE functions. Ignition Switch should be in the Run Position.

Use this function when the PCM has been replaced. PIN code will be needed.

This routine should be used when the WCM/WIN module has been replaced. This procedure will (1) learn VIN and PIN code if not already programmed in WCM/WIN, and (2) transfer Secret Key from PCM to WCM/WIN. All Keys/Fobs previously programmed with this WCM/WIN will be irretrievably lost and cannot be reprogrammed again. If PCM DTC P0633 is present, run PCM Replace routine, not WCM/WIN Replace. Performing this procedure unnecessarily may affect the vehicle malfunction. Absolutely do not to use this procedure unnecessarily! Refer to the Factory Service Manual for the details.

This routine will erase the WCM VIN. Absolutely do not to use this procedure unnecessarily! This routine can be useful, eg. after replacing a WCM module with a used one. Performing this procedure unnecessarily may affect the vehicle malfunction. Absolutely do not to use this procedure unnecessarily!

This function should be used when an additional Key/FOBIK need to be added or when the RFH module has been replaced. Ignition Switch should be in the Lock State.

This function should be used when an additional Key/FOBIK need to be added or when the RFH module has been replaced. Ignition Switch should be in the Lock State. Refer to the Factory Service Manual for the details.

This function should be used when an additional Key/FOBIK need to be added or when the RFH module has been replaced. Ignition Switch should be in the Lock State. RFH Flash Part Number should be 68252600AA or greater for this routine. Refer to the Factory Service Manual for the details.

This function is to be used when programming a new ignition key or re-programming an existing. It will program the WIN functionality along with the RKE functions. Ignition Switch should be in the Run Position.

This routine will allows you to change or reset the WCM PIN Code. Absolutely do not to use this procedure unnecessarily! This routine can be useful, eg. after replacing a WCM module with a used one. Performing this procedure unnecessarily may affect the vehicle malfunction. Absolutely do not to use this procedure unnecessarily!

This procedure will show the WCM LIN bus configuration and allows you to edit the settings. Absolutely do not use this procedure unless necessary. Incorrect settings may lock the immobilizer. Refer to the Factory Service Manual for the details. Performing this procedure unnecessarily may affect the vehicle malfunction. Absolutely do not to use this procedure unnecessarily!

This routine will allow you to convert a currently programmed Administrator Key to a KeySense Key and vice versa. Please note that there must be at least one Administrator Key programmed at all times. The 5-digits vehicle Immo PIN code will be needed.

This function allows you to read Immo PIN Code from the Siemens WCM module.

This function allows you to write PCM Current VIN Number.

This function should be run when a new PEM (Passive Entry Module) is installed or new FOBIK keys are programmed or replaced. It will program the vehicle PIN, transfer the secret key data, and transfer the FOBIK IDs to the PEM. Ignition Switch should be in the Run Position.

This function should be used when an additional Key/FOBIK need to be added or when the RFH module has been replaced. Ignition Switch should be in the Lock State.

This function should be used to erase all ignition Keys/FOBIKs currently programmed to the vehicle. It is not possible to erase only one selected Key/FOBIK. Ignition Switch should be in the RUN State.

This function erases all ignition keys currently programmed to this vehicle. Ignition Switch should be in the Run Position.

This function reset WIN vehicle configuration. Use this function ONLY when the gateway vehicle configuration has changed after the WIN Replaced function has been run. This should not be run under normal circumstances. Ignition Switch should be in the Run Position.

This function should be run when the ELV and WCM/WIN have been replaced. NOTE: Both components must always be replaced together. Ignition Switch should be in the Run Position. Refer to the Factory Service Manual for the details.

This function is to be used when programming a new ignition key or re-programming an existing. It will program the WIN functionality along with the RKE functions. Ignition Switch should be in the Run Position.

This function allows you to verify proper connection between PEM and Door Handles. Ignition Switch should be in the RUN Position.

This function should be used when an additional Key/FOBIK need to be added or when the RFH module has been replaced. Ignition Switch should be in the Lock State.